Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Construction in Felton, CA | Daly City Construction
We’re Daly City Construction, an independent CWS service in Lompico and throughout Felton and the surrounding Santa Cruz Mountains. We install, repair, and rebuild CWS cabinetry and countertop packages in mountain homes where factory specs meet hillside reality. The difference here is simple: Felton’s redwood-damp air and pier-and-beam floors put stress on CWS cabinet boxes, seams, and finishes in ways you won’t see down in Scotts Valley or Santa Cruz proper. Call (866) 505-5254 for a free estimate on your CWS project.
Why Felton Residents Choose Us for CWS Service
CWS cabinet lines are sold through a range of channels, which means a lot of Felton homeowners end up with boxes that were never properly fitted to their house in the first place. We’ve spent years correcting those installs. Our crews know the CWS ready-to-assemble and assembled cabinet lines, their quartz and granite countertop programs, and the bath vanity and linen cabinet series well enough to order the right fillers, panels, and hardware without guesswork.
Noel Cabrera, who runs Daly City Construction, grew up in Daly City’s Westlake district and trained in construction technology at City College of San Francisco before putting in years on residential and light commercial jobs across San Mateo and San Francisco counties. He learned early that a cabinet is only as good as the wall and floor behind it. That matters twice as much up here, where a Felton cabin’s redwood framing can be a half-inch out of plumb and the crawlspace underneath breathes moisture all winter.
When we work on CWS cabinets in Felton, we check the box condition, the wall, the floor, and the moisture source before we touch a single panel. That’s the part most installers skip. It’s also the part that determines whether your CWS kitchen holds up for ten years or starts delaminating in three.
Styles & brands we work with
Common CWS Construction Problems We Solve in Felton
- Thermofoil and laminate faces peeling. Felton’s fog cycles and interior moisture from wet winters work the glue lines on thermofoil doors and drawer fronts. We see it most on sink bases and lower cabinets near exterior walls. The fix is usually replacing the affected doors with CWS OEM matched faces, then addressing the moisture source so it doesn’t return.
- Particleboard and MDF boxes swelling at the toe kick and sink base. Slow leaks, winter humidity, and damp crawlspaces all push moisture into the box core. Once the box swells, it’s done. We replace the cabinet, and we correct the drainage or crawlspace venting that fed the problem.
- Quartz and granite seams opening on pier-and-beam floors. Felton hillside homes move seasonally. When the floor flexes, countertop seams can separate and cabinet frames rack out of square. We shim and relevel before we reset the tops, otherwise the seam just opens again next winter.
- Factory cabinet runs arriving 1/2 to 2 inches off on out-of-plumb walls. Older Felton cabins and ranch homes with redwood framing rarely have straight walls. We order the correct fillers and panels, shim properly, and build the layout so the gaps aren’t visible. No sloppy caulk-and-hope finishes.
- Discontinued CWS door matching for partial remodels. If one cabinet face is damaged or you’re extending a layout, we track down the closest CWS match, including OEM doors and drawer fronts where they’re still available, and quality aftermarket hardware where it outperforms the original.
CWS Service in Felton: What Local Conditions Mean for Your Equipment
Here’s the thing most our General Contractor in Felton pages won’t tell you. Felton sits inside the Cal Fire wildland-urban interface, which means Chapter 7A ignition-resistant requirements shape material choices on any remodel. Your cabinet and countertop decisions have to answer to two forces at once: year-round redwood-damp from fog, rain, and leaf litter, and defensible-space material rules that limit what you can put against the house. That pairing doesn’t exist in Scotts Valley or Santa Cruz proper. It’s unique to the WUI-designated mountain communities, and it means a CWS cabinet package picked at a showroom in the valley may be exactly the wrong specification for a cabin off Felton Empire Road.
On one mid-century cabin there, we pulled out a CWS thermofoil run whose sink base had swollen and whose doors were peeling from years of winter damp. We rebuilt the layout with new CWS boxes, solid filler panels, and quartz counters set level on a shimmed pier-and-beam floor. Then we fixed the drainage grading and crawlspace venting that had been feeding the moisture the whole time. The cabinets were the symptom. The cabin was the cause.
CWS Models & Products We Service in Felton
We work across the CWS product range: ready-to-assemble and assembled kitchen cabinet lines in both painted and thermofoil finishes, the quartz and granite countertop programs paired with those packages, bath vanity and linen cabinet lines, and the laminate and solid-surface countertop offerings. When a match matters, we order CWS OEM doors, drawer fronts, and hardware. When the original hardware is the weak point, we use aftermarket hinges, slides, and sealants that hold up better to mountain moisture. Our position is simple: if a cabinet box is swollen or delaminated beyond the frame, we replace it. Patching a soft, water-damaged box just kicks the problem to next winter.
See the difference
Before
After
Before
After
Before
AfterCWS Service Pricing in Felton
What you’ll pay depends on the scope: a single vanity swap lands at the low end, while our Home Remodeling in Felton for a full kitchen with quartz counters and structural floor work runs higher. Here are the ranges we work within in Felton:
| Service | Price Range |
|---|---|
| Kitchen Remodel | $14,000 – $45,000 |
| Small Kitchen Remodel | $9,000 – $20,000 |
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Bathroom Vanity Installation | $800 – $3,000 |
Several factors move the number. Structural floor or wall correction adds labor. Seam matching on existing quartz costs more than a fresh layout. WUI-compliant material choices can shift pricing on exterior-adjacent work. Every estimate starts with a site visit so we can see the actual conditions, not a guess. Call (866) 505-5254 to schedule a free estimate, and we’ll give you a written line-item quote.
Serving Felton, CA — Our Local Coverage Area
We’re based in the Felton area and also provide CWS service in Ben Lomond, and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs – CWS Construction in Felton
Only if the moisture source is addressed before or during install. CWS thermofoil and MDF boxes are not designed for sustained damp exposure, and Felton’s fog, rain, and crawlspace humidity will work the glue lines and swell the box cores. We check drainage grading, crawlspace venting, and kitchen ventilation as part of every CWS cabinet install. Call (866) 505-5254 if your cabinets are already showing peel or swell.
Usually not. On Felton hillside lots with pier-and-beam floors, seasonal movement opens seams that can be re-cut and re-set once the substrate is leveled and shimmed. If the seam edges are chipped or the slab itself is cracked, replacement may be cheaper than repeated repair. We’ll inspect it and give you the straight answer. Call (866) 505-5254 for a free assessment.
Often yes. We track current and recently discontinued CWS door and drawer front inventory to get as close to the original finish as possible. Where an exact OEM match doesn’t exist, we’ll show you the closest options and let you decide. For Felton kitchens, we recommend matching the replacement door profile and glaze tone rather than trying to blend age-faded finishes with brand-new laminate.
Interior cabinets and countertops are generally not directly regulated by Chapter 7A, but exterior-adjacent material choices, deck connections, and any wall penetrations are. We coordinate CWS interior packages with the WUI-compliant exterior work so your whole project clears inspection without rework.
Plan for three to seven working days once materials are on site, depending on whether we’re correcting out-of-plumb walls, shimming floors, or rebuilding a water-damaged box. Older Felton ranch homes with redwood framing rarely accept a factory run without some adjustment, and rushing that step is how you end up with visible fillers and racked frames. Call (866) 505-5254 and we’ll give you a schedule that reflects your actual house, not a brochure.
Service Areas Near Felton
Our crews work all over the Felton service area and the surrounding mountain communities. We regularly take calls from Mount Hermon and CWS service in Mount Hermon, plus Scotts Valley and CWS service in Scotts Valley for projects that span both the mountains and the valley floor.
Book Your CWS Service in Felton Today
Tell me what the house needs, not what you think it needs, then we’ll figure out the right fix. That’s how we approach every CWS job in Felton. If your cabinets are peeling, your seams are opening, or you’re planning a full kitchen rebuild, call (866) 505-5254 and we’ll schedule a free estimate.
Written by Noel Cabrera, Owner at Daly City Construction, serving Felton and the Santa Cruz Mountains since the company’s first mountain remodel.